Lab testing: a node through temperature, humidity and vibration in the chamber. The loop, step by step: 1. A device waits inside an environmental chamber. 2. Sensor, link, edge and console stand ready. 3. The chamber drops to minus forty. 4. The device is exercised as it cools. 5. Time and place are fixed to every sample. 6. Every sample is signed by the rig. 7. Heat and humidity follow in turn. 8. Instruments confirm the response took effect. 9. The edge verifies every signature first. 10. Limits are compared with the specification. 11. Only a confirmed result leaves the edge. 12. The report is signed at the desk. 13. The console shows the evidence with the alert. 14. Record, proof and action are archived together. 15. Everything settles back to idle.

01 / 15

A device waits inside an environmental chamber

Nexus Observatory

Test and qualification

Lab testing

Environmental, RF, power and EMC, on the bench.

Lab testing, inside Test and qualification: environmental test series, MIL-STD-810H-type tailored testing, telecom outdoor equipment tests, electromagnetic compatibility and more. Every item is traced to its specification, from IEC 60068-2 series to MIL-STD-810H, and runs on the open Observatory Protocol.

Plan with usArchitectureThe protocol

Technologies: 7
At the frontier: 0
Protocol functions: 3 of 12
Industries served: 4

At a glance

Environmental test series

Standard tests for heat, cold, damp heat, vibration, shock and temperature change. In lab testing, part of Test and qualification, the environmental and EMC testing layer holds environmental test series, drawn against IEC 60068-2 series and used beside transport and packaging tests on the same sites.

O problema

Environmental, RF, power and EMC, on the bench

Datasheets promise performance in conditions nobody’s site will see. Buyers, auditors and regulators need results they can check, from tests they can repeat. Without independent, repeatable tests, every comparison between suppliers is a comparison between marketing documents; qualification replaces claims with measured results, published either way.

Key facts

Specification: IEC 60068-2 series
Specification: IEEE 693 (seismic design for substations) · NEBS GR-63-CORE (earthquake zones)
Specification: ETSI EN 300 019-2-4
Specification: IEC 61000-6-2 and 61000-6-4 · CISPR 32 and CISPR 35
Specification: MIL-STD-810H

Components

Environmental test bay with climatic chamber and shaker
Automatic weather station (AWS) to WMO siting practice
Particulate monitoring station and sensor node
Compact X-band weather radar / ISAC sensing node on a lattice tower top
Street small-cell pole with an air-quality node
“AI tower in a box”
Hardware security module, 1U, in an edge rack
Data hall row pair with cold-aisle containment

Interfaces

Radio: Ethernet

Where it works

Seismic qualification
Electromagnetic compatibility

In the story below

The system, part by part
Assembly
Installation
Deployment
Connections
Operação
Failure and recovery
Scale and federation
What you get

Scenes · 13

Next steps

Plan a deployment Open the Field Deployment Studio See Test and qualification Talk to sales

Test and qualification · Lab testing
Environmental, RF, power and EMC, on the bench
Datasheets promise performance in conditions nobody’s site will see. Buyers, auditors and regulators need results they can check, from tests they can repeat. Without independent, repeatable tests, every comparison between suppliers is a comparison between marketing documents; qualification replaces claims with measured results, published either way.
O que faz
Environmental test series
Standard tests for heat, cold, damp heat, vibration, shock and temperature change. In lab testing, part of Test and qualification, the environmental and EMC testing layer holds environmental test series, drawn against IEC 60068-2 series and used beside transport and packaging tests on the same sites.
Specification
IEC 60068-2 series
Environmental and EMC testing
Seismic qualification
Anchorage and shake testing for equipment in seismic zones. In lab testing, part of Test and qualification, the environmental and EMC testing layer holds seismic qualification, drawn against IEEE 693 and NEBS GR-63-CORE. We build it into every site for lab testing against that standard, and keep its version and its test results on the site’s record.
Specification
IEEE 693 (seismic design for substations) · NEBS GR-63-CORE (earthquake zones)
Environmental and EMC testing
Telecom outdoor equipment tests
Test specifications for equipment in outdoor and unprotected locations. In lab testing, part of Test and qualification, the environmental and EMC testing layer holds telecom outdoor equipment tests, drawn against ETSI EN 300 019-2-4. We build it into every site for lab testing against that standard, and keep its version and its test results on the site’s record.
Specification
ETSI EN 300 019-2-4
Environmental and EMC testing
Electromagnetic compatibility
Emissions and immunity so equipment neither causes nor suffers interference. In lab testing, part of Test and qualification, the environmental and EMC testing layer holds electromagnetic compatibility, drawn against IEC 61000-6-2 and 61000-6-4 and CISPR 32 and CISPR 35. We build it into every site for lab testing against that standard, and keep its version and its test results on the site’s record.
Specification
IEC 61000-6-2 and 61000-6-4 · CISPR 32 and CISPR 35
Environmental and EMC testing
MIL-STD-810H-type tailored testing
Life-cycle environmental tailoring with methods for altitude, sand, rain, icing and shock. In lab testing, part of Test and qualification, the environmental and EMC testing layer holds MIL-STD-810H-type tailored testing, drawn against MIL-STD-810H and used beside highly accelerated life testing on the same sites.
Specification
MIL-STD-810H
Confiança
Proved before it is trusted
A node joins a network for lab testing only after its hardware root of trust answers an attestation challenge. Its keys stay in secure hardware, its software arrives signed and every record it makes for lab testing carries a signature, so anyone downstream can check where a value came from.
Evidências
Traced to its specifications
We trace each part of lab testing to its specification: IEC 60068-2 series, MIL-STD-810H and ETSI EN 300 019-2-4. We keep the versions, configurations and test results of lab testing as signed records, so a buyer or an auditor can check what was delivered against what was specified.
Normas
IEC 60068-2 series · MIL-STD-810H · ETSI EN 300 019-2-4 · IEC 61000-6-2 and 61000-6-4
Operations
Every node watched, every incident closed
The operations console shows every node of a network for lab testing with its state, its plan and its evidence. An alert arrives with its data and a runbook, acknowledging it opens a work order, and an incident for lab testing closes only when the operator records the cause and verifies the fix.
Failure and recovery
When a node fails, the fleet knows first
When a node for lab testing goes silent or a sensor drifts, the node buffers its data and fails over to a second link where the site has one. The alert carries the evidence a responder needs, and the record for lab testing loses nothing and counts nothing twice.
Atualizações
Updates in rings, with rollback
Software and configuration reach a fleet for lab testing in rings: one canary site first, then a few, then all, each ring gated on health and data completeness. A failed gate stops the wave, and each node for lab testing returns to its last good release without a site visit.
What you get
Qualification and the works-with programme
The conformance tool and test plans are open. Device and software qualification, the works-with programme and field trial management are contracted. Works-with testing gives makers a recognised way to show their products join any grid built on the specification, with results published either way.
Talk to sales Partner with us
Next step
Lab testing, planned with you
Tell us the sites, the systems lab testing must work with and the outcome you need, with a map or a list of addresses if you have one. An engineer replies with a survey proposal, a design and a scope for lab testing, and the plan grows from one site to the network you need.
Plan a deployment Open the Field Deployment Studio See Test and qualification

See it from every side.

Each opens as a full-screen presentation: deeper pages on the same subject, explainers, stories, guided tours of the places, network scenes and the observatories that came before.

All presentations

01O que é

Environmental and EMC testing.

How a remote site is powered, stored, distributed, cooled, sealed, tested, grounded, held up and kept safe, from a solar-powered sensor to a hybrid microgrid on a guyed mast. Each technology below carries what it is, what we do with it, and the standard it is drawn against.